Concrete Slab Cost & Volume Estimator

Precision multi-layer project budgeting: Materials, Sub-Base, Reinforcement, Labor & Equipment

Picking a location sets the ready-mix, excavation and labor rates below to that area's typical level. You can still type your own local prices afterwards. Slab prices by state.

ft
ft
in
$
$ /sq ft
inches
$ /yd³
$ /lin ft
$ /sq ft

Closer spacing uses more steel and raises the rebar cost.

$
$ /sq ft
$

Not charged when bagged concrete is selected.

$
$
$
$ /sq ft
%
%
Live Estimate
Estimated Total Project Budget
$8,716.09
$10.90 / sq. ft.
$117.27 / m²
Based on U.S. national average rates
Order Volume (w/ Waste)
13.58 yd³
Net: 12.35 yd³
Or Bagged Equivalent
612 bags
80-lb pre-mix bags
Total Surface Area
800 sq ft (74.3 m²)
Order volume: 10.38 m³
Estimated Wet Weight
53,167 lbs
Perimeter: 120 ft
Concrete
Labor
Prep/Base
Rebar
Forms

A scaled plan of your slab: rebar grid at the spacing you chose, support chairs about every 3 to 4 ft, and the recommended control-joint saw cuts (2.5 times the thickness in inches, in feet, capped at 15 ft). It redraws as you change the inputs.

Driveway Sizes and Costs (5 in thick)

Project Size Concrete (+10% waste) DIY Materials Installed
1-car, short 10 × 20 ft (200 sq ft) 3.40 yd³ $760–$1,080 $1,610–$2,790
1-car, long 12 × 40 ft (480 sq ft) 8.15 yd³ $1,570–$2,340 $3,610–$6,370
2-car, short 20 × 20 ft (400 sq ft) 6.79 yd³ $1,310–$1,950 $3,010–$5,320
2-car 20 × 40 ft (800 sq ft) 13.58 yd³ $2,420–$3,700 $5,820–$10,380
3-car 30 × 40 ft (1,200 sq ft) 20.37 yd³ $3,480–$5,400 $8,580–$15,380
Installed low end: plain broom-finish slab with ready-mix at $150/yd³ plus a $120 delivery fee, forms and labor at $3.50/sq ft. High end: the calculator's default scope (adds a vapor barrier and #4 rebar at 18 in, labor at $5.00/sq ft) plus 25% contractor overhead and profit. DIY materials: the cheaper of ready-mix or $6.50 80-lb bags, plus forms, up to vapor barrier and rebar. Site excavation and a gravel base are extra (about $1.40 to $3.30 per sq ft).

Recommended Specifications

Thickness5 in for cars; 6 in for RVs, trucks or a delivery route
Concrete strength3,500 PSI air-entrained in freeze-thaw areas (the IRC minimum for exposed flatwork there); 4,000 PSI where de-icing salt is used
Base4 to 6 in of compacted crushed stone; more on soft or clay soil
Reinforcement#4 rebar at 12 to 18 in centers on chairs
SlopeAt least 1/8 in per ft so water runs off, away from the garage
Control jointsEvery 12.5 ft or closer, panels close to square

What Adds to a Driveway Bill

  • Tear-out: breaking up and hauling away an old slab runs about $3 to $4 per sq ft. Price it with the removal cost calculator.
  • The apron: the section between the street and the sidewalk usually belongs to the city, needs its own permit and is often built to a city detail (thicker, sometimes 6 in).
  • Grading: a sloped lot may need fill or a retaining edge before forming.
  • Decorative work: a stamped driveway runs about $14 to $22 per sq ft.
  • Pumping: a long drive the truck cannot reach may need a line pump ($400 to $800 for a job).

Protecting a New Driveway

Keep cars off a new driveway for at least 7 days, and heavy trucks off for the full 28 days. In the first winter, avoid rock salt: it attacks young concrete. Sand gives traction without the damage. A penetrating sealer applied after the slab has cured helps it resist salt and oil.

Frequently Asked Questions

A 20 x 40 ft driveway at 5 inches thick costs about $5,820 to $10,380 installed, which is $7 to $13 per sq ft. It takes 13.58 cubic yards of concrete.

Five inches with rebar is the standard recommendation for passenger cars. Use 6 inches if RVs, heavy trucks or delivery vans will use it. Local codes vary, so check with your building department.

At least 3,500 PSI air-entrained concrete in areas with freeze-thaw cycles, and 4,000 PSI where de-icing salt is used. Mild climates can use 3,000 PSI.

Wait at least 7 days for a passenger car and 28 days for heavy vehicles.

Related Guides

Slab Estimating & Editorial Engineering Team

Construction Cost Estimators & Civil Engineering Analysts
Our team specializes in structural flatwork estimating, concrete mix designs, and civil building codes (ACI 302.1R, ASTM C94). All calculators and cost guides are rigorously validated against live contractor material price sheets, regional aggregate indexes, and real-world project bids.