Concrete Slab Cost & Volume Estimator

Precision multi-layer project budgeting: Materials, Sub-Base, Reinforcement, Labor & Equipment

Picking a location sets the ready-mix, excavation and labor rates below to that area's typical level. You can still type your own local prices afterwards. Slab prices by state.

ft
ft
in
$
$ /sq ft
inches
$ /yd³
$ /lin ft
$ /sq ft

Closer spacing uses more steel and raises the rebar cost.

$
$ /sq ft
$

Not charged when bagged concrete is selected.

$
$
$
$ /sq ft
%
%
Live Estimate
Estimated Total Project Budget
$13,560.40
$11.30 / sq. ft.
$121.64 / m²
Based on U.S. national average rates
Order Volume (w/ Waste)
24.44 yd³
Net: 22.22 yd³
Or Bagged Equivalent
1100 bags
80-lb pre-mix bags
Total Surface Area
1,200 sq ft (111.5 m²)
Order volume: 18.69 m³
Estimated Wet Weight
95,700 lbs
Perimeter: 140 ft
Concrete
Labor
Prep/Base
Rebar
Forms

A scaled plan of your slab: rebar grid at the spacing you chose, support chairs about every 3 to 4 ft, and the recommended control-joint saw cuts (2.5 times the thickness in inches, in feet, capped at 15 ft). It redraws as you change the inputs.

Foundation Slab Sizes and Costs (4 in floor, thickened edge)

Project Size Concrete (+10% waste) Installed
Small house / ADU 24 × 32 ft (768 sq ft) 15.56 yd³ $5,400–$10,800
Ranch, 1,200 sq ft 30 × 40 ft (1,200 sq ft) 22.76 yd³ $8,400–$16,800
Ranch, 1,600 sq ft 32 × 50 ft (1,600 sq ft) 29.33 yd³ $11,200–$22,400
Ranch, 2,000 sq ft 40 × 50 ft (2,000 sq ft) 35.53 yd³ $14,000–$28,000
Installed range uses the monolithic slab rate of $7–$14/sq ft (4 in floor with thickened edge, see our methodology). Concrete includes the thickened edge and waste.

Recommended Specifications

Floor thickness4 in typical (the IRC minimum is 3.5 in); thicker under bearing walls and point loads per the plans
Thickened edge12 in or wider, 12 to 18 in deep or to frost depth, with 2 or more #4 bars
Concrete strength2,500 PSI minimum for foundations not exposed to weather; most builders order 3,000 or more
Under the slab4 to 6 in of compacted stone, 6-mil or heavier vapor retarder, and insulation where the energy code requires it
FrostFootings below the local frost line (often 36 to 48 in in cold states) or a frost-protected shallow foundation design
DesignFollow stamped plans or your building department's details; soil conditions set the final design

What the Price Includes (and What It Does Not)

The per-square-foot figure covers the slab and its thickened edges: forming, base, vapor retarder, rebar, concrete, placing and finishing. It does not cover the soil test or engineering, permits and inspections, plumbing and electrical rough-in under the slab, termite treatment, under-slab insulation, or major grading. On a house, those can add as much again as the slab itself, so get them priced separately.

When a Slab Is the Right Foundation

Slabs suit flat lots, warm and mixed climates, and single-story homes where you want no steps at the doors. They are the cheapest common foundation. A crawl space or basement makes more sense on sloped lots, where frost is very deep, or when you want easy access to pipes and ducts. Our slab vs. crawl space comparison goes through the trade-offs. Structural foundations need a design that meets your local code, so treat these numbers as a budget, not a plan.

Frequently Asked Questions

About $7 to $14 per sq ft for a monolithic slab with thickened edges, before plumbing rough-in, engineering and permits.

Roughly $8,400 to $16,800 for a 30 x 40 ft monolithic slab. It takes about 22.8 cubic yards of concrete including the thickened edges and waste.

Typically 12 to 18 inches deep and at least 12 inches wide, but it must reach below the frost line where codes require it. Your plans or building department set the exact size.

Usually, yes. A slab needs less excavation, no stem walls and no floor framing. A crawl space costs more but gives access to plumbing and works better on sloped lots.

Related Guides

Slab Estimating & Editorial Engineering Team

Construction Cost Estimators & Civil Engineering Analysts
Our team specializes in structural flatwork estimating, concrete mix designs, and civil building codes (ACI 302.1R, ASTM C94). All calculators and cost guides are rigorously validated against live contractor material price sheets, regional aggregate indexes, and real-world project bids.