Concrete Garage Slab Cost
Garage floor slab costs for 1, 2 and 3-car garages, and the choices that matter: thickness, vapor barrier, thickened edges and slope to the door.
A garage floor slab costs about $7 to $14 per sq ft installed at 5 inches thick, so a 24 × 24 ft two-car garage runs about $4,250 to $7,540 for the slab. Thickened edges for a monolithic pour add concrete and digging on top of that.
Concrete Slab Cost & Volume Estimator
Precision multi-layer project budgeting: Materials, Sub-Base, Reinforcement, Labor & Equipment
Picking a location sets the ready-mix, excavation and labor rates below to that area's typical level. You can still type your own local prices afterwards. Slab prices by state.
Closer spacing uses more steel and raises the rebar cost.
Not charged when bagged concrete is selected.
A scaled plan of your slab: rebar grid at the spacing you chose, support chairs about every 3 to 4 ft, and the recommended control-joint saw cuts (2.5 times the thickness in inches, in feet, capped at 15 ft). It redraws as you change the inputs.
| Scope Item / Material Description | Amount |
|---|
Enter the total your contractor quoted. We compare it with a benchmark for the same slab and scope you set in the calculator: materials at your entered prices plus labor at the regional standard rate, before any overhead or profit. Make sure the calculator scope (base, rebar, finish, pump, demolition) matches what the bid includes.
Optional: enter the bid's line items to see where the markup sits
Enter the forecast for pour day. The check follows ACI 306R (cold weather) and ACI 305R (hot weather) and estimates the surface evaporation rate that drives plastic shrinkage cracking.
Garage Slab Sizes and Costs (5 in thick)
| Project | Size | Concrete (+10% waste) | DIY Materials | Installed |
|---|---|---|---|---|
| 1-car | 12 × 24 ft (288 sq ft) | 4.89 yd³ | $1,010–$1,470 | $2,240–$3,910 |
| 1.5-car / workshop | 16 × 24 ft (384 sq ft) | 6.52 yd³ | $1,270–$1,890 | $2,910–$5,120 |
| 2-car, compact | 20 × 22 ft (440 sq ft) | 7.47 yd³ | $1,430–$2,130 | $3,300–$5,820 |
| 2-car | 24 × 24 ft (576 sq ft) | 9.78 yd³ | $1,800–$2,720 | $4,250–$7,540 |
| 3-car | 24 × 36 ft (864 sq ft) | 14.67 yd³ | $2,580–$3,970 | $6,260–$11,170 |
Recommended Specifications
| Thickness | 5 in for cars; 6 in for a shop with lifts, heavy tools or trucks |
|---|---|
| Concrete strength | 3,500 PSI (the IRC minimum for garage floors in severe weather areas); 4,000 PSI if salty slush drips off cars |
| Vapor barrier | 6-mil or heavier polyethylene under the slab (IRC R506.2.3), especially if the garage will be heated or finished |
| Edges | Thickened edge 12 in wide and 12 to 18 in deep for monolithic slabs, or a stem wall on footings in deep-frost areas |
| Reinforcement | #4 rebar at 12 to 18 in centers, plus 2 bars around the edge |
| Slope | Toward the door or a floor drain, so melt water runs out |
Monolithic Slab or Stem Wall?
A monolithic slab pours the floor and a thickened edge in one go. It is the cheaper choice where frost is shallow. On a 24 × 24 ft garage, deepening the edge to 18 in takes about 4.06 extra cubic yards of concrete, plus trenching for the edge ($250 to $600 at 18 in deep in typical soil).
Where the frost line is deep (often 36 to 48 in or more in northern states), codes usually want footings below frost, so builders pour a footing and stem wall first and the floor slab inside it. That costs more but protects against frost heave. Your building department decides which one your garage needs. Estimate footing concrete with the footing calculator.
Before You Pour a Garage Floor
- Floor drain or trench drain: it has to be set before the pour, with the slab sloped toward it.
- Anchor bolts: sill-plate bolts or straps go into the wet edge concrete at the spacing your plans call for.
- Door step-down: a small rebate at the overhead door keeps water from running under the door seal.
- Coatings: if you plan an epoxy floor, ask for a steel-trowel finish and wait for the slab to dry fully first.
Frequently Asked Questions
A 24 x 24 ft garage floor at 5 inches thick costs about $4,250 to $7,540 installed, or $7 to $14 per sq ft. It needs 9.78 cubic yards of concrete before thickened edges.
Five inches is the usual recommendation for cars. Use 6 inches for a workshop with a car lift, heavy machines or trucks.
The IRC calls for a 6-mil vapor retarder under slabs of enclosed spaces, with some exceptions for unheated garages. Most builders install one anyway because it is cheap and stops moisture from damaging coatings and stored items.
A monolithic thickened-edge slab is cheaper and common where frost is shallow. In deep-frost areas codes usually require footings below the frost line, which means a stem wall foundation. Ask your building department.