Concrete Slab Cost & Volume Estimator

Precision multi-layer project budgeting: Materials, Sub-Base, Reinforcement, Labor & Equipment

Picking a location sets the ready-mix, excavation and labor rates below to that area's typical level. You can still type your own local prices afterwards. Slab prices by state.

ft
ft
in
$
$ /sq ft
inches
$ /yd³
$ /lin ft
$ /sq ft

Closer spacing uses more steel and raises the rebar cost.

$
$ /sq ft
$

Not charged when bagged concrete is selected.

$
$
$
$ /sq ft
%
%
Live Estimate
Estimated Total Project Budget
$1,204.04
$12.04 / sq. ft.
$129.60 / m²
Based on U.S. national average rates
Order Volume (w/ Waste)
1.36 yd³
Net: 1.23 yd³
Or Bagged Equivalent
62 bags
80-lb pre-mix bags
Total Surface Area
100 sq ft (9.3 m²)
Order volume: 1.04 m³
Estimated Wet Weight
5,317 lbs
Perimeter: 40 ft
Concrete
Labor
Prep/Base
Rebar
Forms

A scaled plan of your slab: rebar grid at the spacing you chose, support chairs about every 3 to 4 ft, and the recommended control-joint saw cuts (2.5 times the thickness in inches, in feet, capped at 15 ft). It redraws as you change the inputs.

Shed Pad Sizes and Costs (4 in thick)

Project Size Concrete (+10% waste) DIY Materials Installed
8 × 10 shed 10 × 8 ft (80 sq ft) 1.09 yd³ (49 × 80-lb bags) $360–$490 $700–$1,190
10 × 10 shed 10 × 10 ft (100 sq ft) 1.36 yd³ (62 × 80-lb bags) $410–$570 $840–$1,430
10 × 12 shed 12 × 10 ft (120 sq ft) 1.63 yd³ (74 × 80-lb bags) $460–$650 $970–$1,680
12 × 16 shed 16 × 12 ft (192 sq ft) 2.61 yd³ (118 × 80-lb bags) $630–$940 $1,450–$2,560
12 × 20 shed / small garage 20 × 12 ft (240 sq ft) 3.26 yd³ $750–$1,130 $1,770–$3,140
Installed low end: plain broom-finish slab with ready-mix at $150/yd³ plus a $120 delivery fee, forms and labor at $3.50/sq ft. High end: the calculator's default scope (adds a vapor barrier and #4 rebar at 18 in, labor at $5.00/sq ft) plus 25% contractor overhead and profit. DIY materials: the cheaper of ready-mix or $6.50 80-lb bags, plus forms, up to vapor barrier and rebar. Site excavation and a gravel base are extra (about $1.40 to $3.30 per sq ft).

Recommended Specifications

Thickness4 in; 5 in with thickened edges if a riding mower, ATV or car is stored inside
SizeMatch the shed floor exactly, or 1 to 2 in smaller per side so rain drips off the siding, not onto the pad
Concrete strength3,000 PSI; 3,500 PSI air-entrained where it freezes
Base4 in of compacted crushed stone
AnchoringJ-bolts or wedge anchors along the sill line (follow the shed maker's plan)
Moisture6-mil poly under the slab keeps ground moisture off stored tools

Concrete Pad or Gravel Pad?

A gravel pad (compacted stone inside a timber frame) is cheaper and drains well. It suits sheds with their own wood floor on skids. A concrete pad costs more but becomes the floor itself: it is flat, rodent-proof, easy to sweep, and it lets you bolt the walls down and roll heavy equipment in. Choose concrete for workshops, mower and ATV storage, or any shed without a built-in floor.

Getting the Shed to Fit

  • Square: measure both diagonals of the forms; they must match before you pour.
  • Level: a shed pad should be level (not sloped like a patio), or the doors will bind.
  • Access: plan a ramp or a flush threshold at the door if you will roll equipment in.
  • Setbacks and permits: many towns limit how close a shed can sit to the property line, and some require a permit above a certain size. Check permit rules first.

Frequently Asked Questions

About $970 to $1,680 installed at 4 inches thick, or $460 to $650 in materials to do it yourself. It needs 1.63 cubic yards of concrete (74 bags of 80-lb mix).

Four inches for a storage shed. Use 5 inches with thickened edges if you will park a riding mower, ATV or car inside.

Gravel is cheaper and fine for sheds with their own floor. Concrete costs more but gives a flat, rodent-proof floor you can anchor to, which is better for workshops and heavy equipment.

No. Make it the same size or slightly smaller, so rain running down the walls drips onto the ground rather than onto the slab and under the siding.

Related Guides

Slab Estimating & Editorial Engineering Team

Construction Cost Estimators & Civil Engineering Analysts
Our team specializes in structural flatwork estimating, concrete mix designs, and civil building codes (ACI 302.1R, ASTM C94). All calculators and cost guides are rigorously validated against live contractor material price sheets, regional aggregate indexes, and real-world project bids.