Concrete Slab Cost & Volume Estimator

Precision multi-layer project budgeting: Materials, Sub-Base, Reinforcement, Labor & Equipment

Picking a location sets the ready-mix, excavation and labor rates below to that area's typical level. You can still type your own local prices afterwards. Slab prices by state.

ft
ft
in
$
$ /sq ft
inches
$ /yd³
$ /lin ft
$ /sq ft

Closer spacing uses more steel and raises the rebar cost.

$
$ /sq ft
$

Not charged when bagged concrete is selected.

$
$
$
$ /sq ft
%
%
Live Estimate
Estimated Total Project Budget
$4,253.36
$10.63 / sq. ft.
$114.46 / m²
Based on U.S. national average rates
Order Volume (w/ Waste)
5.43 yd³
Net: 4.94 yd³
Or Bagged Equivalent
245 bags
80-lb pre-mix bags
Total Surface Area
400 sq ft (37.2 m²)
Order volume: 4.15 m³
Estimated Wet Weight
21,267 lbs
Perimeter: 80 ft
Concrete
Labor
Prep/Base
Rebar
Forms

A scaled plan of your slab: rebar grid at the spacing you chose, support chairs about every 3 to 4 ft, and the recommended control-joint saw cuts (2.5 times the thickness in inches, in feet, capped at 15 ft). It redraws as you change the inputs.

Interior Floor Sizes and Costs (4 in thick)

Project Size Concrete (+10% waste) DIY Materials Installed
Room addition 12 × 16 ft (192 sq ft) 2.61 yd³ (118 × 80-lb bags) $630–$940 $1,450–$2,560
Workshop / studio 20 × 24 ft (480 sq ft) 6.52 yd³ $1,290–$2,060 $3,330–$6,020
Basement floor 24 × 36 ft (864 sq ft) 11.73 yd³ $2,140–$3,530 $5,820–$10,620
Large basement 30 × 40 ft (1,200 sq ft) 16.30 yd³ $2,870–$4,790 $7,970–$14,620
Installed low end: plain broom-finish slab with ready-mix at $150/yd³ plus a $120 delivery fee, forms and labor at $3.50/sq ft. High end: the calculator's default scope (adds a vapor barrier and #4 rebar at 18 in, labor at $5.00/sq ft) plus 25% contractor overhead and profit. DIY materials: the cheaper of ready-mix or $6.50 80-lb bags, plus forms, up to vapor barrier and rebar. Site excavation and a gravel base are extra (about $1.40 to $3.30 per sq ft).

Recommended Specifications

Thickness4 in (IRC minimum 3.5 in); 5 to 6 in under heavy machines
Concrete strength2,500 PSI minimum for interior slabs not exposed to weather; 3,000 PSI is common
Vapor retarder6-mil polyethylene minimum (IRC R506.2.3); 10 or 15-mil under finished floors; about $0.25 to $0.45 per sq ft
Base4 to 6 in of compacted stone or clean sand
FinishSteel trowel ($1.00 to $1.50 per sq ft); no broom texture indoors
JointsSaw-cut 4 to 12 hours after finishing, lined up with walls and columns

Moisture Comes First Indoors

A slab can be strong enough to walk on in a day and still be too wet for flooring for months. Before laying vinyl, wood, carpet or an epoxy coating, test the slab with the method the flooring maker names (a calcium chloride test or an in-slab relative humidity probe) and wait until it passes. A good vapor retarder under the slab is the cheapest insurance: once the slab is poured, it cannot be added.

Polished, Stained or Covered?

If the concrete will be the finished floor, plan it from the start. Polished concrete needs a flat, dense, steel-troweled surface and careful protection during construction. Stains and dyes show every patch and mark. If you will cover the slab with tile, wood or vinyl, flatness matters more than looks. Radiant heat tubing, plumbing and floor outlets all have to be placed before the pour.

Frequently Asked Questions

About $5,820 to $10,620 for a 24 x 36 ft basement at 4 inches thick, before polishing or coatings. It takes 11.73 cubic yards of concrete with waste.

Four inches is standard for basements, additions and workshops (the IRC minimum is 3.5 inches). Go thicker under heavy equipment.

Yes, the IRC calls for a 6-mil vapor retarder under slabs of heated spaces, and flooring makers often want a thicker one. It stops ground moisture from damaging flooring and coatings.

Concrete reaches design strength in about 28 days, but drying for flooring often takes longer. Test the moisture level as the flooring maker requires before installing.

Related Guides

Slab Estimating & Editorial Engineering Team

Construction Cost Estimators & Civil Engineering Analysts
Our team specializes in structural flatwork estimating, concrete mix designs, and civil building codes (ACI 302.1R, ASTM C94). All calculators and cost guides are rigorously validated against live contractor material price sheets, regional aggregate indexes, and real-world project bids.